- Online only
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
We are AMA Garden original spare parts Dealers at low at unbeatable prices and a service center with repair service able to advise you on the purchase of the most suitable spare part to quickly resolve any maintenance or repair issues for Chainsaw AMX 26.10 - 92604.
In the following table, look for the model of the Chainsaw and the respective parts of the code.
| Motosega AMX 26.10 | ||
| # | Part Num. | Description |
| 1 | 92789 | Engine |
| 2 | 92790 | Crankcase |
| 3 | 92791 | Crankshaft components |
| 4 | 63806 | Bearing 6001 |
| 5 | 63807 | Oil seal 12×28×6 |
| 6 | 63801 | Needle bearing washer |
| 7 | 92793 | Needle bearing 8×11×9 |
| 8 | 63803 | Piston pin circlip |
| 9 | 63804 | Piston |
| 10 | 63805 | Piston ring |
| 11 | 92794 | Cylinder |
| 12 | 63821 | Igniter washer |
| 13 | Standard | Flameout wire 0.5×410 |
| 14 | Standard | Bolt, hexagon hole M4×18 |
| 15 | Standard | Spring Washer 4 |
| 16 | Standard | Washer 4 |
| 17 | 89815 | Ignition Coil assembly - NEW 98905 |
| 18 | 63812 | Elbow |
| 19 | 63802 | Piston pin |
| 20 | 63818 | Key 3×3.5×10 |
| 21 | 63808 | Oil seal 12×22×5 |
| 22 | 63820 | Nut M8×1 |
| 23 | 89816 | Rotor assembly |
| 24 | Standard | Washer 5 |
| 25 | Standard | Spring washer 5 |
| 26 | Standard | Bolt, hexagon hole M5×22 |
| 27 | 12207 | Spark plug (LD L8RTF) |
| 28 | 63786 | Air intake tube |
| 29 | Standard | Screw M4×14 |
| 30 | 84917 | Supporting bead |
| 31 | 63825 | Muffler gasket |
| 32 | 88216 | Muffler assembly |
| 33 | 92795 | Muffler cover |
| 34 | Standard | Bolt, hexagon hole M5×50 |
| 35 | 63879 | Joint |
| 36 | 63814 | Pressure pipe 2.5×6×48 |
| 37 | 63813 | Clip |
| 38 | 92796 | Top cover |
| 39 | Standard | Tapping screw ST4.2×16 |
| 40 | 63852 | Stopper |
| 41 | 63847 | Engine switch |
| 42 | 92797 | Rear handle cover |
| 43 | 63788 | Bolt |
| 44 | 63844 | Cap |
| 45 | 63858 | Throttle rod |
| 46 | 92798 | Trigger control rack |
| 47 | Hollow rivet | |
| 48 | 92799 | Choke |
| 50 | 63842 | Damper |
| 51 | 63856 | Trigger roller 5×25 |
| 52 | 95110 | Throttle trigger |
| 53 | 57803 | Trigger torsion rod spring |
| 54 | 63797 | Carburettor pressure pipe |
| 55 | 63857 | Fuel output pipe |
| 56 | 88204 | Fuel tube circlip |
| 57 | 95111 | Rear handle |
| 58 | 63866 | Air cleaner plate |
| 59 | 63794 | Screw M5×45 |
| 60 | 63862 | Seal |
| 61 | 63863 | Carburetor |
| 62 | 63865 | Air cleaner base |
| 63 | 63867 | Cleaner |
| 64 | 63868 | Cleaner cover |
| 65 | 95112 | Air filter cover |
| 95113 | Knob | |
| 68 | 95114 | Brake assembly |
| 69 | 95115 | Front handle guard |
| 70 | 64030 | Weight |
| 71 | 64031 | Weight torsion rod spring |
| 72 | 64036 | Screw M5×32 |
| 75 | 95116 | Clutch cover |
| 75a | Heat isolation film for clutch cover | |
| 75b | Rectangular heat isolation film | |
| 76 | 88207 | Passively conical gear |
| 77 | 57808 | Active conical gear |
| 78 | 88206 | Tension block |
| 79 | 64049 | Tension block plate |
| 80 | 64044 | Brake control rod |
| 81 | 64046 | Brake spring |
| 82 | 64045 | Brake strap |
| 83 | 58122 | Pin 3×9 |
| 84 | 95117 | Secondary pull-rod |
| 85 | Standard | Roller 3×14 |
| 86 | 95118 | Main lever |
| 87 | Standard | Tapping screw ST4.2×12 |
| 88 | 95119 | Spring cover |
| 89 | 95120 | Spring |
| 90 | 95121 | Spring base |
| 91 | 64038 | Returned torsion rod spring |
| 92 | Standard | Locknut M5 |
| 93 | 73839 | Nut M8 |
| 94 | 63882 | Clutch assembly |
| 98 | 63837 | Clutch washer |
| 99 | 63836 | Clutch drum(3/8) |
| 100 | 63835 | Needle bearing 10×13×13 |
| 101 | 55079 | Worm SCREW |
| 102 | 63834 | Oil pump cover |
| 103 | 63875 | Oil outgoing pipe |
| 104 | 57570 | Oil pump |
| 105 | 63829 | Reduce attrition washer 10×18×1.5 |
| 106 | 63831 | Oil pipe |
| 107 | 57633 | Oil filter |
| 108 | 57633 | Oil filter screen |
| 109 | 63830 | Plate |
| 110 | 88202 | Dustproof sponge block |
| 111 | 88203 | Dustproof sponge piece |
| 112 | 63893 | Heat insulation mat |
| 113 | Standard | Ground wire 0.5×175 |
| 114 | Standard | Bolt, hexagon hole M5×16 |
| 115 | 95122 | Cap assembly |
| 117 | 63890 | Cap gasket 20×30×2 |
| 119 | Base components | |
| 120 | 64075 | Spiked bumper |
| 121 | 95123 | Spiked bumper case |
| 122 | Standard | Tapping screw ST4.8×13 |
| 123 | Standard | Tapping screw ST4.2×13 |
| 124 | Ventilated tube 3.5×6.5×65 | |
| 125 | 90456 | Suction jet |
| 126 | 63833 | Primer bulb |
| 127 | 63771 | Balancer |
| 128 | 63885 | Balancer root |
| 129 | 57507 | Fuel filter |
| 131 | 63883 | Fuel pipe set |
| 134 | 76204 | Screw ST4.2×13 |
| 135 | 63877 | Chain catcher |
| 136 | 63845 | Attachment device |
| 137 | 95124 | Base |
| 137a | Heat isolation film for base | |
| 137b | 88215 | Heat isolation plate for base |
| 138 | 95125 | Starter assembly |
| 139 | 64053 | Air conduct pipe |
| 140 | 64051 | Bossing |
| 141 | Standard | Tapping screw ST4.8×13 |
| 142 | 95126 | Coil spring I |
| 143 | 95127 | Rope sheave |
| 144 | 95128 | Coil spring II |
| 145 | 95129 | Handle |
| 147 | 64060 | Jacket |
| 148 | 95130 | Starter cover |
| 149 | Standard | Tapping screw ST4.8×16 |
| 150 | 63896 | Front handle washer |
| 152 | 95131 | front handle |
| 153 | 63842 | Front handle absorber |
| 154 | 95132 | Gland |
| 155 | 95133 | Ratchet wheel |
| 156 | Scutcheon | |
| 157 | 84928 | 10'' Oregon bar |
| 157 | 73116 | Sprocket Nose Bar 10" 3/8" with "AMA" logo |
| 158 | 71522 | Saw chain (3/8) |
| 158 | ORE7932140 | Saw chain (3/8) |
| 159 | 62006 | Guide bar cover |
You might also like